Is a QW Sewage Pump Right for the Job?

Aug 12, 2026 Leave a message

Article Description

 

The MISLIER QW range covers small building drainage duties as well as much larger wastewater projects. This article explains how to read the model, what is inside the pump, which installation options are available and when QWG or QWP may be a better choice.

One of the shortest enquiries we receive is: "Please quote a 7.5 kW QW pump."

It sounds specific, but it still leaves most of the selection unanswered. The MISLIER catalogue contains several QW pumps with a 7.5 kW motor. They do not deliver the same flow or head, and they may not use the same outlet size. Power tells us how large the motor is. It does not tell us where the pump will operate in the customer's pipe system.

QW is a broad submersible sewage pump family. In the current catalogue, nominal outlet sizes run from 50 to 600 mm and motor power from 0.75 to 250 kW. The smaller models suit building drainage and compact pits, while the larger end of the range is intended for municipal and industrial wastewater duties. Selecting from that range starts with the duty point and wastewater, not with a kilowatt figure.

Reading a QW Model without Guessing

 

qwmodel100QW80-9-4explained500x375Take 100QW80-9-4 as an example. The first number indicates a nominal outlet diameter of 100 mm. QW identifies the submersible sewage pump series. The remaining figures describe a nominal flow of 80 m³/h, a head of 9 m and a 4 kW motor.

That code is a useful filter, not a promise that every installation will receive exactly 80 m³/h. The real flow is where the pump curve meets the resistance of the discharge system. Vertical lift, pipe length, diameter, elbows, valves and the discharge point all affect it. If a project needs 80 m³/h after ten metres of vertical lift and a long horizontal run, the 9 m model code already tells us that the selection needs another look.

The standard catalogue is based on 380 V. Frequency, phase, starting method and any different voltage requirement should be confirmed before the model is finalised. The control arrangement matters too. A small single pump may only need level control and basic protection. A larger station may need duty-standby operation, alternation, a high-level alarm and signals from the pump's protective devices.

What the Standard QW Is Built to Handle

 

The QW hydraulic section uses a large-flow-channel impeller intended for wastewater containing suspended solids and limited fibrous material. The wider passage lowers the chance of blockage compared with a narrow clean-water impeller. It does not make the pump immune to wipes, rope, cloth or a large bundle of laundry fibres. If those materials enter regularly, the wastewater description should say so before a standard QW is selected.qwmotormechanicalsealsoilchamber500x375

Between the pumped liquid and the motor are two mechanical seals arranged in series, with an oil chamber between them. The oil lubricates and cools the seal faces while providing another barrier before water can reach the motor. This is a practical wastewater-pump arrangement, but the seals are still wearing parts. Sand, abrasive grit, dry running and poor installation can shorten their working life.

Thermal and leakage protection varies with pump size and configuration. Larger models can be supplied with additional monitoring, and pumps of 11 kW or more can use a motor cooling arrangement where the installation requires it. These features only help when their signals are connected to a compatible control cabinet. A leakage probe left unwired cannot warn the operator.

The ordinary QW should also be separated from two related options in the catalogue. QWG is the cutting version for wastewater where difficult fibres and entanglement are the main concern. QWP uses stainless-steel construction where corrosion resistance is required. A standard cast-iron QW is often the sensible choice for ordinary sewage, but it should not be sold as a grinder pump or a chemical pump.

Choose the Installation with the Pump

 

qwautomaticcouplingwetwell500x375Automatic coupling, identified by the installation code Z, is common in permanent wet wells. A discharge base is fixed at the bottom of the pit. The pump travels down guide rails and seats on the coupling, so it can later be lifted without a technician undoing the submerged discharge bolts. This is particularly useful in municipal stations, hotels and production facilities where maintenance access matters.

The catalogue also includes fixed dry installation, fixed-base wet installation and mobile arrangements using a flexible hose or hard pipe. Mobile installation may suit temporary drainage or construction work. A permanent station normally benefits from guide rails, a lifting chain, accessible check and isolation valves, and enough overhead space to remove the pump safely.

The installation cannot be decided from the pump model alone. A narrow pit may not leave room for the guide rails or for two pumps. A small working volume can cause frequent starts. A discharge pipe supported by the pump creates mechanical stress. These details do not appear in the motor power, but they have a large effect on reliability.

 

qwqwgqwpthreeproductcomparison500x375

The catalogue's standard operating limits are also worth checking before quotation: liquid temperature up to 40°C, density up to 1050 kg/m³, pH from 5 to 9 and maximum immersion depth of 20 m. Hot kitchen waste, dense sludge or strongly corrosive liquid needs a separate review rather than an automatic QW selection.

For an initial recommendation, send the required flow, total lift, discharge pipe size and route, wastewater source, largest expected solids and the amount of fibrous material. Add the site voltage, installation method and pit dimensions. If a drawing is available, include it. Those details allow the pump curve, solids passage and maintenance arrangement to be checked together.

So, is a QW sewage pump right for the job? For ordinary municipal, industrial and building wastewater, often yes. But the correct answer is a model and installation that match the site-not simply the first QW pump with the requested motor power.