The Optimal Working Time Of Swimming Pool Pump

The pool pump is one of the key equipment to ensure the health and cleanliness of the pool water. Its main function is to ensure that the water quality in the pool is always in the best condition through continuous water circulation, thus providing swimmers with a comfortable and pleasant swimming environment. Specifically, the pool pump promotes the flow of pool water in a closed pipe system, so that the water circulates continuously between the pool and various treatment equipment. This process not only ensures the orderliness and uniformity of the water flow, but also effectively avoids the occurrence of rapids, vortices and stagnant water areas.

Pool water circulation uses a water pump as a power source to enable pool water to flow continuously within a closed pipe and between various equipment and swimming pools, keeping the water flow in the pool orderly and uniform, without rapids, whirlpools, or dead water areas. In this way, the purified water is evenly distributed to each part of the pool during the flow process, and the dirtier sewage in the pool that has not yet been purified is replaced in an orderly manner, allowing it to enter the subsequent equipment of the pool water purification system for purification.

Is it necessary for the pool pump to run 24 hours a day?

We need to analyze this problem in detail according to the situation. If it is an open large public swimming pool with a large flow of people, it will definitely take a longer time to circulate and purify the pool water, so it is very necessary for the water pump to circulate 24 hours a day.

However, for some small indoor commercial or domestic swimming pools, it is completely unnecessary to run the water pump 24 hours a day. As long as the pump is run within a reasonable time period, the water quality can be kept clean. It can be effectively maintained by running 8-12 hours a day according to the season and frequency of use, and circulating the pool water 2-3 times. If the water quality of the swimming pool is good and the environmental conditions are stable, running the pump for 6 to 8 hours a day is usually sufficient. If the environment is poor (such as many trees, strong wind and sand) or the swimming pool is used frequently, the running time of the pump can be appropriately increased.

If the swimming pool pump is allowed to run excessively continuously, it will not only increase the electricity bill burden of users in vain, but may also accelerate the wear of the water pump itself.Therefore, reasonable control and adjustment of the working time of the swimming pool    pump can effectively save energy and extend the service life of the water pump to a certain extent.

When should the pool pump run? During the day or at night?

Starting the pool pump during the day can effectively reduce the excess chlorine in the water. During the day, the ultraviolet rays in direct sunlight will reduce the chlorine content in the pool water. After the pump has been running for a few hours, the chlorine content can be reduced by up to 90%. But at the same time, the operation of the pump will prevent the remaining amount of chlorine from being changed by the sun to resist the excessive influence of the sun. In addition, there is a large flow of people in the swimming pool during the day. Starting the pump at this time will help promote the flow of water, making it difficult for bacteria to grow and debris to fall into the pool, and speeding up the process of pool water circulation. However, the biggest disadvantage of running the pump continuously during the day is that it will greatly increase the energy cost of users. This is not only because the daytime is the peak period of electricity consumption, but also because the efficiency of purification and disinfection of pool water during the day is low. For example, the water pump works with the disinfection equipment for 9 hours during the day to complete the purification work, while it only takes 6 hours at night. However, there will definitely be some differences in the purification effect.

If it is run at night, because the electricity price is lower in many areas at night, running the pump at night can save electricity bills; the temperature is lower at night, the evaporation rate of water slows down, and less water loss is lost when running the pump. However, if the pump does not run long enough when adding disinfectant at night, it may cause uneven distribution of chemicals, affecting the disinfection effect and the efficiency of chemicals.

It can be seen that whether the swimming pool pump is running during the day or at night, there will be corresponding advantages and disadvantages, so it is better to divide the working time of the water pump reasonably and seize the advantages of the two running times to achieve the best filtering effect and operating efficiency.

Generally, we consider it optimal to have a pool pump running for 8 hours per day to perform the circulating filtration work. The pump can be set to run both during the day and at night, with the day handling major impurities and water quality maintenance, and running at night to save energy and run quietly. For example, the pump could be run for a total of 4-6 hours in two periods during the day (such as morning and afternoon), and then run for another 2-4 hours at night to further maintain water quality.

You can choose to start the pump from 10:00 am to 2:00 pm when the sun is shining and the water temperature is highest, which helps to resist the effects of the sun, especially during peak swimming times, and effectively inhibits algae growth and easily removes bacteria and debris. Then you can choose to run the pump again during the off-peak hours of 1:00 am to 5:00 am to save operating costs, and when it is darker, chlorine production will peak at sunrise, which is simply the best of both worlds!

Scan Harry Ge WhatsAPP or Wechat to get connected.